How to Install a Bath Tub
How to Install a Bath Tub
Blog Article
We have uncovered this great article involving How to Install a Bathtub down the page on the net and reckoned it made sense to discuss it with you on this site.
Setting up a bath tub isn't exactly brain surgery, yet it does require solid plumbing, woodworking, and in some cases, tiling skills. Changing an old bath tub with a new one is likewise a reasonably difficult project. If the old bathtub is conveniently accessible, the project can move rapidly; if you need to open up a wall surface to remove the old tub as well as place the brand-new bathtub, the task is a lot harder. In either instance, the task is within a home handyman's skills, although you will require an assistant to vacate the old tub and set in the new one. Make certain you have actually certified yourself for the job and are comfortable trying it. As opposed to employing a service provider to take control of a halfway-completed task, it is better to consider employing one before you begin. Chances are you may need an expert plumber to make tube connections.
This post will certainly aid you mount a brand-new bath tub in your washroom if you have actually currently acquired a brand-new bathtub as well as do not require to alter the plan of your previous water system pipelines.
Your devices as well as material checklist ought to make up the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your installment, after that the first thing you must do is detach the water system. After doing so, switch on the taps to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be rather problematic due to the restricted accessibility that is usually the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the taps. Have a towel prepared for the staying water that will originate from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any type of old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washing machines are in location between the faucet and the sink. Protect the faucet in place with the maker provided backnut. Once the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical faucet adapters. The former kind should be linked to the faucet ends initially, tightening only by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Bath tub
Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wood boards are useful in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 small points.
The following objective is to guarantee that the tub is leveled all round. This can be attained by checking the level and also adjusting the feet on the tub till the level reads level.
To mount faucets, fit the bottom of the furthest adaptable faucet connector to the suitable supply pipe by making a compression sign up with; after that do the same for the other faucet.
Turn on the water system and also examine all joints and also new pipework for leaks and tighten them if necessary. Fill the bathtub and likewise inspect the overflow outlet as well as the typical electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the tub ought to wait up until the tub has been utilized a minimum of once as this will settle it into its final placement.
Planning for the Installment
To start with, the sustaining structure provided with the bath ought to be fitted (if needed) according to the producer's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to make certain that if the faucet includes a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets device to stop stress on the tub.
Fit the versatile tap connectors to the bottom of the two taps making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you utilize all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its final position.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is essential as the installation can move enough to fracture a stiff seal, causing the water to pass through the wall in between the bath and the tiling, causing problems with dampness and also possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your fixtures and installations. They are sold in tubes and also cartridges, and can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to always fill up the bath tub with water before securing, to permit the motion experienced when the bathtub is in use. The sealer can crack relatively very early if you do not consider this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the market. It is recommended to fit the floor tiles using water-resistant or waterproof sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed reading our section about How to Install a Bathtub. Thanks for taking time to read our article post. Do you know another individual who is in the market for the subject? Feel free to share it. Thank you for going through it.
Schedule Your Service
Report this page